Documentation:Streaming HowTo/Stream from Encoding Cards and Other Capture Devices

From VideoLAN Wiki
Jump to navigation Jump to search
VLC Streaming HowTo

Introduction
Streaming, Muxers and Codecs

Main
Easy Streaming
Advanced Streaming Using the Command Line
Command Line Examples

VLM
VLM - Multiple Streaming and Video on Demand

Tutorials and examples
Receive and Save a Stream
Convert files to other formats
Stream a File
Stream a DVD
Stream a DVB Channel
Stream from Encoding Cards and Other Capture Devices
Stream from a DV Camcorder
Streaming for the iPhone

IPv6
Streaming over IPv6
View this alone

Hardware encoding cards

Note: This is possible under GNU/Linux only.

VideoLAN supports two kinds of MPEG-2 encoding cards:

  • Hauppauge WinTV-PVR-250 and WinTV-PVR-350,
  • Visiontech Kfir.

The Hauppauge WinTV-PVR-250/350 gives much better results and is cheaper than the Visiontech Kfir.

Stream with the Hauppauge WinTV-PVR-250/350 card

Install the drivers

First, you will have to patch your kernel (version 2.4) to support the v4l2 API (Video 4 Linux version 2). The patch is available on the Video4Linux HQ. If you use a 2.6 kernel, you only need to build I2C support and the BT848 Video For Linux module.

Once your kernel is ready, install the CK version (currently in development) of the Linux drivers for the Hauppauge WinTV-PVR-250/350. They are hosted on ivtv ck. You will need to patch your kernel to use it with a 2.4. You can also use the CVS version available here: ivtv.sourceforge.net (this version is not developped anymore). Then, you will have to create the device and load the modules; for this, please refer to the documentation shipped with the drivers.

Stream with VLC

Note: You must add --enable-pvr to ./configure to use this feature.

% vlc -vvv --color pvr:///dev/video0:norm=secam:size=720x576:frequency=576250:bitrate=3000000:maxbitrate=4000000 --cr-average 1000 --sout '#rtp{mux=ts,dst=192.168.0.42,port=5004}' --ttl 12

where:

  • /dev/video0 is the device corresponding to the encoding card,
  • norm=secam is name of the standard of the analogic signal (possible values are pal, secam, and ntsc),
  • size=720x576 is the size of the video you want to stream,
  • frequency=567250 is the frequency in kHz of the channel you want to stream,
  • bitrate=3000000 is the average bitrate of the stream,
  • maxbitrate=4000000 is the maximum bitrate of the stream,
  • 1000 is a secret value to work around a bug of the card.
  • 192.168.0.42 is either:
    • the IP address of the machine you want to unicast to;
    • or the DNS name the machine you want to unicast to;
    • or a multicast IP address.
  • 12 is the value of the TTL (Time To Live) of your IP packets (which means that the stream will be able to cross 11 routers).

Stream with the Visiontech Kfir card

Install the drivers

If you want to be able to stream from a Visiontech Kfir card, you need to install its Linux drivers. Download the latest release of the drivers from the drivers download page of the [http://www.linuxtv.org/ LinuxTV web site].

Uncompress the tarball and follow the instructions written in the INSTALL file to compile and install the drivers.

Note: If you have a VIA chipset, you need to disable USB in the BIOS.

Stream

% vlc -vvv --color kfir:///dev/video --sout '#rtp{mux=ts,dst=192.168.0.42,port=5004}' --ttl 12

where:

  • /dev/video is the device corresponding to the Kfir card,
  • 192.168.0.42 is either :
    • the IP address of the machine you want to unicast to;
    • or the DNS name the machine you want to unicast to;
    • or a multicast IP address.
  • 12 is the value of the TTL (Time To Live) of your IP packets (which means that the stream will be able to cross 11 routers).

Software encoding cards

Under GNU/Linux

Install the Video for Linux drivers

If you want to stream from an acquisition card or a webcam, a video4linux driver must be available for it. You can find more information about video4linux and supported devices here.


Compile the right module for your device, and insert it into your kernel. Some video4linux modules are shipped with the 2.4.x and 2.6.x Linux kernels, the patch is available on the Video4Linux HQ.

You can test your device by using any of the listed programs in the Video: TV and PVR/DVR section of this page.


Note that v4l2 modules will also work with VLC.

Stream with VLC

Note: You must add --enable-v4l to ./configure to use this feature.

% vlc -vvv --color v4l:///dev/video:norm=secam:frequency=543250:size=640x480:channel=0:adev=/dev/dsp:audio=0 --sout '#transcode{vcodec=mp4v,acodec=mpga,vb=3000,ab=256,venc=ffmpeg{keyint=80,hurry-up,vt=800000},deinterlace}:rtp{mux=ts,dst=239.255.12.13,port=5004}' --ttl 12

Note: You can find all transcode options on this page : Advanced Streaming Using the Command Line.

where:

  • /dev/video is the device corresponding to your acquisition card or your webcam,
  • norm=secam is name of the standard of the analogic signal (possible values are pal, secam, and ntsc),
  • frequency=543250 is the frequency of the channel in kHz (Warning: for VLC < 0.6.1, Frequency is channel frequency in MHz multiplied by 16),
  • size=640x480 is the size of the video you want (you can also put the standard size like subqcif (128x96), qsif (160x120), qcif (176x144), sif (320x240), cif (352x288) or vga (640x480)),
  • channel=0 is the number of the channel (usually 0 is for tuner, 1 for composite and 2 for svideo),
  • adev=/dev/dsp is the audio device,
  • audio=1 is the number of the audio channel (usually 0 is for mono and 1 for stereo),
  • vcodec=mp4v is the video format you want to encode in (mp4v is MPEG-4, mpgv is MPEG-1, and there is also h263, DIV1, DIV2, DIV3, I420, I422, I444, RV24, YUY2),
  • acodec=mpga is the audio format you want to encode in (mpga is MPEG audio layer 2, a52 is A52 i.e. AC3 sound),
  • vb=3000 is the video bitrate in Kbit/s
  • ab=256 is the audio bitrate in Kbit/s
  • venc=ffmpeg allows to set the encoder to use, where:
    • keyint=80 is the maximal amount of frames between two key frames
    • hurry-up allows the encoder to decrease the quality of the stream if the CPU can't keep up with the encoding rate
    • vt=800000 is the tolerance in kbit/s for the bitrate of the outputted video
  • deinterlace tells VLC to deinterlace the video on the fly,
  • 192.168.0.42 is either:
    • the IP address of the machine you want to unicast to;
    • or the DNS name the machine you want to unicast to;
    • or a multicast IP address.
  • 12 is the value of the TTL (Time To Live) of your IP packets (which means that the stream will be able to cross 11 routers).

Stream with DirectShow

Note: This is only possible under Windows.

Install your peripheral drivers

You need to install your peripherals under Windows with the appropriate drivers. Nothing else is necessary.

Stream with VLC in command line

% C:\Program Files\VideoLAN\VLC\vlc.exe -vvv -I rc --ttl 12 dshow:// vdev="VGA USB Camera" adev="USB Camera" size="640x480" --sout=#rtp{mux=ts,dst=239.255.42.12,port=5004}

Note: You need to precise the complete path to find vlc program or to launch the command from the correct directory.

  • vvv is to activate the verbose mode
  • rc is to activate the remote control interface (MS/DOS console)
  • 12 is the value of the TTL (Time To Live) of your IP packets (which means that the stream will be able to cross 11 routers),
  • vdev="VGA USB Camera" is the name of the video peripheral that DirectShow will use (this is only an exemple),
  • adev="USB Camera" is the name of the audio peripheral,
  • size="640x480" is the resolution (you can also put the standard size like subqcif (128x96), qsif (160x120), qcif

(176x144), sif (320x240), cif (352x288) or vga (640x480)).

  • 239.255.42.12 is either:
    • the IP address of the machine you want to unicast to;
    • or the DNS name the machine you want to unicast to;
    • or a multicast IP address.

Mac OSX

Note that VLC does not support streaming from live video or audio sources on Mac OSX.

This page is part of official VLC media player Documentation (User GuideStreaming HowToHacker GuideModules)
Please read the Documentation Editing Guidelines before you edit the documentation
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.